Model C7G [SLP-C7F (free version) Installation (for C7G firmware 2.x.x - 6.4.x)]

You can download the installation file for the SLP-C7F for C7G firmware 2.x.x to 6.4.x.
Please check the privacy policy at the bottom of this page, then fill in the customer information form to register and download the file.

Important Notice: To customers using HMI firmware ver. 5.0.4

Thank you for using the SLP-C7.

A problem was found with the display unit (HMI) firmware ver. 5.0.4 that you installed using SLP-C7. Please download the latest version of the SLP-C7F (ver. 2.4.0 or later) and update the HMI firmware to ver. 5.0.5.

File Information

DeviceModel C7G
SoftwareSLP-C7
Version2.6.3 (Japanese/English/Chinese)
SizeApprox. 19.2 MB
SLP-C7IconF/W Ver 1.x.xF/W Ver 2.x.x～6.4.x
Ver 2.6.3
SLP-C7F_40
×◎/○
Ver 1.0.0
SLP-C7F_41
◎×

◎: Read/write possible

○: Read/write possible (a firmware version mismatch message pops up when writing data)

　Read: Parameters not available with the firmware are set to their default values.

　Write: For parameters not available with the firmware, data is not written.

　To edit data offline, read the settings from the controller.

　SLP-C7F versions 2.6.3 and 1.0.0 can be installed on a single PC.

　The firmware version of the C7G"" is the firmware version of its MAIN block.

　You can confirm the version on the FIRMWARE VERSION screen on the C7G.

[SLP-C7F System Requirements]

ItemDescription
HardwareHardwareWindows PC with an Intel CPU
Recommended: Core i3–7 series, 1.5 GHz or faster (1 GHz min.)
Operating system for
SLP-C7F ver. 1.5.0 or later		Japanese/English Windows
32-bit/64-bit
Windows 10 Ver 1909 - 20H2
Windows 11 Ver 22H2 or later
Note: Operation on other Windows systems is not guaranteed.
MemoryRecommended: 4 GB or more (2 GB min.)
Hard disk driveRecommended free space: 20 GB or more (10 GB min.)
Display1366 x 768 resolution or higher, 32-bit color or higher is recommended
Japanese input methodWindows-compatible Japanese IME
PDF viewerAdobe Acrobat Reader DC or later
USB portAt least 1 port is required to connect to the C7G controller with a USB cable.
Ethernet portAt least 1 port is required to connect to the C7G controller via Ethernet.
MicroUSB cableMicro-USB to USB cable*1
MouseRequired
KeyboardRequired
OtherNotice
*1. Azbil's USB loader cable (model No. 81441177-001) cannot be used because it is a Mini-USB cable.
Use a commercially available Micro-USB data cable. (A charge-only Micro-USB cable cannot be used.)

If you would like to download, please agree to the terms and conditions and fill in the information on the form that will be displayed.

Privacy Policy for the Protection of Personal Information

This section explains how to handle personal data on the "Products and Services Site (https://aa-industrial.azbil.com/))" (hereinafter referred to as the "Website"), a website operated by the Advanced Automation Company (hereinafter referred to as the "AAC") of Azbil Corporation (hereinafter referred to as the "Company").
 

We handle personal information collected and provided by the Website as follows.

1.    Policy for the Protection of Personal Information

We will handle personal information collected and provided by customers in an appropriate manner in compliance with laws and other regulations concerning the protection of personal information. We also comply with Azbil Privacy Policy for the Protection of Personal Information.
 

2.    Purpose of Use of Personal Information

Except for cases stipulated by laws and regulations, AAC uses the personal information collected and provided by customers on  the Website for the following purposes.
 

1) Company name: Azbil Corporation

For more information about the Company, please refer to the link for the representative and the location of the head office.
 

2) Privacy administrator: Azbil Corporation, Advanced Automation Company
General Manager, Control Products Marketing Department
Contact: Please see “4. Disclosure, Correction, Deletion, etc. of Personal Information” below.
 

3) The types and purposes of use of personal information collected and provided by customers on  the Website are as follows.

<Type of personal information>
・  Name, email address, company name, department / office, address, phone number, and other personal information provided by customers in inquiries or on  the Website

<Purpose of Use of Personal Information>
・  Provision of information on the azbil Group and its products and services (including company brochures, catalogs, and corporate magazines) by mail, e-mail such as e-mail magazines, fax, telephone, and other means
・  Information on exhibitions, events, seminars, campaigns, surveys, and gifts which the azbil Group performs or participates in 
・  Surveys of the use of the azbil Group products and services and the environment in which they are used, and marketing activities
・  Information provided through sales activities when the azbil Group determines that its products and services are useful to customers
・  Responding to Customer Inquiries

3.    Joint Use of personal information

Personal information collected and provided by customers on  the Website will be shared within the following scope.
 

1) Items of personal information to be shared
Name, email address, company name, department / office, address, phone number, and other personal information provided by you in inquiries or on the Website

2) Purpose of Joint Use
As described in 3) of “2. (Purpose of Use of Personal Information) “

3) Scope of joint users
Affiliates of the azbil Group

4) Name of the person responsible for the management of Joint Use of the Personal Information
Azbil Corporation, Advanced Automation Company
General Manager, Control Products Marketing Department

5) Company name, address, and name of representative
Company name: Azbil Corporation
For more information about the Company, please refer to the link for the representative and the location of the head office.

4.  Disclosure, Correction, Deletion, etc. of Personal Information

We will promptly respond to requests from the customers for disclosure, correction, addition or deletion of personal information, or withdrawal of consent provided by the customer on the Website.  , .  For requests under this paragraph 4, please contact us via the following.

<Contact for personal information>
Azbil Corporation, Advanced Automation Company
Sales Promotion Group, Control Products Marketing Department, Fujisawa Technology Center Techno Center

You may also use the Contact Form if you wish to make a complaint to us replating to your privacy.

5. Changes to this Privacy Policy

We may modify or amend this Privacy Policy from time to time.  Any changes we may make to this Privacy Policy in the future will be posted on the Website with the date of revision.  
 

 

Creationed on July 17, 2024